E-mail: zzdybriquette@163.com
Contact Us

Zhengzhou Dayang Briquette Machinery Co.,Ltd
Add: Industrial Zone, Zhengzhou City, Henan Province, China
Contact: Simba Lee
Tel/Fax: +86-371-57114464
Mobile: +86-13526658007

Skype: simba58007

Wechat: lee58007
E-mail: zzdybriquette@163.com

Home > News > Content
Coal Briquette Plants Equipment Commissioning Steps
Apr 16, 2018

Coal Briquette Plants equipment commissioning steps


ZHEGNZHOU DAYANG BRIQUETTE MACHINERY CO., LTD-- BRIQUETTE MACHINE PRODUCTION LINE PROFESSIONAL Email: zzdybriquette@163.com

5 tons per hour coal briquettes plant.jpg

The coal briquette plants equipment has a wide range of uses, and it can fully press and form powdered materials such as various coal powders (coking coal, lignite, viscous coal, anthracite, etc.), ore powder, dry powder, slag, etc. There are many types of briquette ball presses and the power is different. When selecting, it is decided according to the customer's output.


Briquette Press Machine production line equipment debugging steps:


1. The single Briquette Press Machine production line carries out empty test run. The sequence is carried out by the following equipment one by one. Check whether the motor running direction is correct, whether the main machine under the Briquette Press Machine is running normally, and whether the temperature rise of the bearing is too high or not. If there is an abnormality in the addition of grease, if it is abnormal, stop and check the fault and remove it before starting the test again.


2. The whole load test of the Briquette Press Machine is started by the following equipment one by one. The Briquette Press Machine is running normally after the whole line machine is running normally. Add a small amount of material, gradually to normal, check the pressure ball machine production line whether the machine is boring, the current is too large, the chute is smooth discharge, such as an exception, from the station after the stop, check, remove the exception Drive again.


3, Briquette Press Machine whole line trial production, generally 4-8 hours of continuous operation, there must be no abnormal circumstances, if any occur, from stop to stop after the stop, re-operation after troubleshooting, time recalculated.


4, in the Briquette Press Machine production process, the material moisture should be strictly controlled, the control position is generally at the mixer. When the material is too dry, the two hemispheres and the broken ball are likely to appear when the ball is pressed. When the material is too wet, the Briquette Press Machine  can easily cause the ball ball machine to stick the ball to the ball without sticking out the ball and stuffy cars. Generally, when the ball is balled into the ball, the moisture is 18-20% when the binder is formed of lime and clay; the moisture is 10-12% when the binder is formed of pulp or humic acid; and the composite type is used. When the agent is molded, the moisture content is 11-13%; when the binder is used for bitumen molding, the moisture content is 2-4%; the binder-free aged lignite is formed when the moisture content is 12-18%; and the binderless weathered anthracite coal is extruded. When the moisture content is 15-18%, the binder-free dry powder has a moisture content of less than 2%.


5. The debugging process of the Briquette Press Machine production line is not only the adjustment test of the process flow and Briquette Press Machine equipment, but also the operation, maintenance personnel training, internship, and exercise process. Therefore, it is necessary to make full use of the commissioning phase of the Briquette Press Machine production line. With production command personnel, the formation of operating teams, training teams, training teams, familiar with the process, master equipment operating procedures and operating techniques, so that pressure ball machine production line officially put into operation as soon as possible, to play a greater economic efficiency.

500 press machine (2).jpg  briquette press[1].jpg

More COAL BRIQUETTE MACHINE related knowledge, please pay attention: www.dayang-briquettepress.com

customers site 3.jpg

ZHENGZHOU DAYANG BRIQUETTE MACHINERY CO., LTD

Add:  No.1,Industrial Zone of Nanyang Village, Zhengzhou City, Henan Province, China

Contact: Simba Lee

Tel: +86-371-63782063

Mobile: +86-13526658007

Fax: +86-371-63782062 

Skype: simba58007

E-mail: zzdybriquette@163.com

website:www.dayang-briquettepress.com

Copyright © Zhengzhou Dayan Briquette Machinery Co.,Ltd All rights reserved.